null
close
close
close

How to Replace Haven & HavenPlus In Duct UV Lamps

WARNING

Unplug unit from the electrical outlet before starting replacement procedure.

Note: Wear disposable, non-absorbent protective gloves prior to replacement procedure in case of accidental breakage of glass.

1. Rotate the Air+Health Haven ballast assembly counterclockwise until it stops. See figure 1.

2. Remove the ballast assembly and lamp from the mounting base. See figure 2.

3. Remove the lamp from the lamp socket. See figure 3.

4. Install the replacement lamp into lamp socket. You can handle the lamp with bare hand but we recommend using gloves. If you do touch the lamp with bare hands wipe off the glass with the supplied alcohol wipe.

5. Position the ballast assembly power cord 90° to the viewport hole on the mounting base. See figure 1.

6. Slide the lamp though the hole in the mounting base.

7. Press the ballast against the mounting base. Rotate the ballast assembly clockwise until it stops and is locked in place. See figure 4.

8. After assembly is firmly in place, plug the power supply cord back into the standard electrical outlet. Check lamp operation by looking through the viewport hole. A blue glow should be seen in the duct.

9. After replacing the lamp, make sure to install the Lamp Replacement Label. Print the date on the label and apply to the side of ballast assembly.

Note: If blue light leaks through any portion of plenum and/or around mounting plate, unplug power supply cord immediately and seal affected areas and/or rotate ballast and repeat step #7 above.

10. UV lamps contain a small amount of mercury, like a typical fluorescent lamp. Check with your local waste management authority for local disposal or recycling requirements. According to the EPA's Universal Waste Rule, these types of lamps may be disposed of into household waste.

WARNING

Never touch broken lamp or internal contents of lamp. The lamp contains mercury.

Note: In case of accidental exposure to internal contents of lamp, wash hands and any other affected skin area with mild detergent. Remove affected clothing immediately. If skin surface is pierced, seek medical attention immediately.

Figure 1

Figure 3

Figure 2

Figure 4

How to Replace Haven & HavenPlus In Duct UV Lamps

WARNING

Unplug unit from the electrical outlet before starting replacement procedure.

Note: Wear disposable, non-absorbent protective gloves prior to replacement procedure in case of accidental breakage of glass.

1. Rotate the Air+Health Haven ballast assembly counterclockwise until it stops. See figure 1.

2. Remove the ballast assembly and lamp from the mounting base. See figure 2.

3. Remove the lamp from the lamp socket. See figure 3.

4. Install the replacement lamp into lamp socket. You can handle the lamp with bare hand but we recommend using gloves. If you do touch the lamp with bare hands wipe off the glass with the supplied alcohol wipe.

5. Position the ballast assembly power cord 90° to the viewport hole on the mounting base. See figure 1.

6. Slide the lamp though the hole in the mounting base.

7. Press the ballast against the mounting base. Rotate the ballast assembly clockwise until it stops and is locked in place. See figure 4.

8. After assembly is firmly in place, plug the power supply cord back into the standard electrical outlet. Check lamp operation by looking through the viewport hole. A blue glow should be seen in the duct.

9. After replacing the lamp, make sure to install the Lamp Replacement Label. Print the date on the label and apply to the side of ballast assembly.

Note: If blue light leaks through any portion of plenum and/or around mounting plate, unplug power supply cord immediately and seal affected areas and/or rotate ballast and repeat step #7 above.

10. UV lamps contain a small amount of mercury, like a typical fluorescent lamp. Check with your local waste management authority for local disposal or recycling requirements. According to the EPA's Universal Waste Rule, these types of lamps may be disposed of into household waste.

WARNING

Never touch broken lamp or internal contents of lamp. The lamp contains mercury.

Note: In case of accidental exposure to internal contents of lamp, wash hands and any other affected skin area with mild detergent. Remove affected clothing immediately. If skin surface is pierced, seek medical attention immediately.

Figure 1

Figure 2

Figure 3

Figure 4

to top